Top 10 Ice Maker Connection Wall Plate

This Eastman 60233 Pex Pre-assembled Ice Maker Outlet Box is designed for recessed residential applications. It has a 1/2 inch Crimp PEX inlet connection and a 1/4-inch OD compression outlet with a rough opening of 5-3/4-inch width x 4-7/8-inch height x 3-1/2-inch diameter.

The outlet box comes complete with a pre-installed 1/4-turn ball valve, support bracket, and a faceplate cover of dimensions 8-1/4-inch width x 7-5/16-inch height. It is built with one-piece box and flange design. Valves governed by this Standard are intended for service at temperatures between 34⁰ F (1⁰ C) and 180⁰ F (82⁰ C), with an allowable working pressure rating not less than 125 PSI (862 kPa).

This Eastman 60232 Sweat Pre-assembled Ice Maker Outlet Box is designed for recessed residential applications. It has a 1/2 inch Sweat inlet connection and a 1/4-inch OD compression outlet with a rough opening of 5-3/4-inch width x 4-7/8-inch height x 3-1/2-inch diameter.

The outlet box comes complete with a pre-installed 1/4-turn ball valve, support bracket, and a faceplate cover of dimensions 8-1/4-inch width x 7-5/16-inch height. It is built with one-piece box and flange design. Valves governed by this Standard are intended for service at temperatures between 34⁰ F (1⁰ C) and 180⁰ F (82⁰ C), with an allowable working pressure rating not less than 125 PSI (862 kPa).

This Eastman 60242 Crimp PEX Pre-assembled Ice Maker Outlet Box is designed for recessed residential applications. It has a 1/2 inch Crimp PEX inlet connection and a 1/4-inch OD compression outlet with a rough opening of 5-3/4-inch width x 4-7/8-inch height x 3-1/2-inch diameter.

The outlet box comes complete with a pre-installed 1/4-turn ball valve, installed hammer arrester, support bracket, and a faceplate cover of dimensions 8-1/4-inch width x 7-5/16-inch height. It is built with one-piece box and flange design. Valves governed by this Standard are intended for service at temperatures between 34⁰ F (1⁰ C) and 180⁰ F (82⁰ C), with an allowable working pressure rating not less than 125 PSI (862 kPa).

Product Description

Are you replacing a 5+ year-old ice maker connector hose or hooking up a new ice maker? This 15 ft. Braided Stainless Steel Ice Maker Connector from Certified Appliance Accessories is just what you need. It is corrosion-resistant inside and out plus bends freely for easier installation in cramped spaces.

From the Manufacturer

Ice Maker Connectors (15-Foot)

Product Description

The Eastman 41033 Ice Maker Connector has a 1/4-inch comp x 1/4-inch comp connection and is 5-feet long. The supply line features a PVC core, multi-filament braided nylon reinforcement, a clear vinyl outer shell and a grade 304 stainless steel braided exterior that is designed to prevent kinking and crimping making it long-lasting. It consists of nickel-plated brass nuts which ensure secure fitting.
Eastman’s 5′ Stainless Steel Icemaker Hose is the standard in icemaker supply lines. This flexible supply line resists corrosion and enables easy installation.
MAINTAINANCE: For use with water in accessible locations only.
• Shut off the water before installing.
• Inspect product before installing. Do not use if damaged in any way.
• Metal nuts – HAND-TIGHTEN, plus ¼ turn with a wrench.
• Do not over tighten.
• Do not use thread lubricants, tape, or putty.
• Do not expose to corrosive materials.
• Over tightening, using lubricants or exposure to corrosive materials can damage nut, connector, valves, or appliance and cause failure, leaking, or flood and property damage.
• This part must be inspected after installation and every six months thereafter. Replace if damaged, leaking or corroded.
• DO NOT reuse
• CAUTION: Improper installation can cause leaks with water damage.

From the Manufacturer

Eastman’s 5′ Stainless Steel Icemaker Connector is the standard in icemaker supply lines. Its quality is determined by what you can’t see. The supply line features a pvc core, multi-filament braided nylon reinforcement, a clear vinyl outer shell, and a grade 304 stainless steel braided exterior that is designed to prevent kinking and crimping. This flexible supply line resists corrosion and is easy to install.

Stainless Steel Ice Maker Supply Line Hose 10 Ft (120-in) Burst Proof 1/4″ Compression Connections – Lead Free

This is an Everflow Supplies lead free flexible ice maker supply line, made of stainless steel braided tube. In particular, it has a length of 120 inch and it has two 1/4 inch compression fittings on both ends. Furthermore, upc, nsf and csa approved the part for meeting the lead free nsf 61-g standards.

6-foot pex line with built-in flare connections. Perfect water line for coiling behind a refrigerator, freezer, and/or tight space. This is the preferred water line to use over copper. Copper tends to oxidize over time and also is not friendly in kinks and/or tight spacing. For peace of mind replace your water lines with this pex line. With built-in flares, it is easy to install and quick to change out. This is not a GE OEM product. The GE brand names and logos are the registered trademarks of their respective owners. Any use of the GE brand name or model designation for this product is made solely for purposes of demonstrating compatibility. “The trademarks, logos, and service marks (collectively the “Trademarks”) displayed herein Supplying Demand are registered and unregistered trademarks of Supplying Demand, its affiliates, and others. Nothing contained herein should be construed as granting, by implication, estoppel, or otherwise, any license or right to use any trademark displayed herein without the written permission of Supplying Demand or such third party that may own the trademark displayed herein. Your misuse of the trademarks displayed herein, or any other content on this website, except as provided herein, is strictly prohibited.”

This is an Everflow Supplies lead free flexible ice maker supply line, made of stainless steel braided tube. In particular, it has a length of 24 inch and it has two 1/4 inch compression fittings on both ends. Furthermore, upc, nsf and csa approved the part for meeting the lead free nsf 61-g standards.