The Best Gas Appliance Flex Hose

Product Description

LASCO 10-1215 LASCO 10-1215 Flexible Coated Gas Appliance Supply Line, 72-Inch, 3/8-Inch OD Connector with 1/2-Inch MIP X 1/2-Inch FIP Fittings. For indoor or outdoor use. Yellow safty coating – corrugated stainless steel. For use with natural gas or propane. Connect to gas dryers! Larsen Supply a third generation family owned and operated company with over 80 years of experience has the largest retail plumbing line in the industry today with over 7000 packaged and 16,000 bulk SKU’s. We pride ourselves on service, selection and support! All Lasco merchandise if warranted to be free of manufacturing defects. Please revert to retail place of purchase for resolution of any possible plumbing questions, warranty or defective part replacement.

From the Manufacturer

LASCO 10-1215 Flexible Gas Dryer Connector Line, 3/8-Inch Diameter with 1/2-Inch Fittings, 72-Inch Long. 3/8-Inch X 72-Inch Gas Appliance Connector, Flexible Stainless Steel, Safety Coating, 1/2-Inch Pipe Thread Ends. Indoor or outdoor use. Yellow Safety Coated. Corrugated Stainless Steel. For Use With Natural Gas or Propane. To Connect Gas Dryers.

BrassCraft’s 3/8 In. Female Flare (1/2 In. MIP) EFV x 1/2 In. MIP x 72 In. Safety+PLUS Gas Appliance Connector is 1/2 In. OD (3/8 In. ID) with a maximum operating capacity of 49,100 BTU’s. This Safety+PLUS gas connector combines excess flow technology with the advanced corrosion resistance of ProCoat, to provide a safer gas connector for home and family. In the event of a gas line rupture or disconnect, the Safety+PLUS valve restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. BrassCraft’s stainless steel gas connector is protected with a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products. ProCoat coating is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

Product Description

High BTU gas connector for use with boilers, commercial water heaters, gas meters, gas packs/rooftop HVAC units, furnaces, and tankless water heaters

From the Manufacturer

This Dormont gas connector is CSA Design Certified domestically and internationally for indoor and outdoor use with natural, manufactured, mixed, liquefied petroleum, and LP-gas air mixtures Durable, naturally corrosion-resistant 304 stainless steel construction offers an exclusive no-neck design to increase flexibility Quality flared end fittings create a metal to metal seal to ensure integrity in critical applications Manufactured domestically in the USA, all Dormont gas connectors are 100 percent leak tested to ensure consistent quality you can trust.

Product Description

Dormont 0240892 Gas Appliance Connector Kit 48 In. Long 5/8 In. Outlet Diameter

From the Manufacturer

This Dormont gas connector is CSA Design Certified domestically and internationally for indoor and outdoor use with natural, manufactured, mixed, liquefied petroleum, and LP-gas air mixtures Durable, naturally corrosion-resistant 304 stainless steel construction offers an exclusive no-neck design to increase flexibility Quality flared end fittings create a metal to metal seal to ensure integrity in critical applications Manufactured domestically in the USA, all Dormont gas connectors are 100 percent leak tested to ensure consistent quality you can trust Safety Shield coating provides extra corrosion protection from accidental contact with common household chemicals

Product Description

ProCoat, 1/2″ Female Iron Pipe x 1/2″ Male Iron Pipe x 72″, Stainless Steel Gas Connector, 1/2″ OD x 3/8″ ID, 49,100 BTU, Engineered With Added Safety In Mind, Proprietary Polymer Coating Withstands Prolonged Exposure To Harsh Household Chemicals, UV Rays & Salt, Apply To The Corrugated Stainless Steel Connector Using Advanced Powder Coat Technology, Coating Is Baked Directly Onto The Connector Surface At High Temperatures To Provide A Uniform Coating Over The Entire Length Of The Connector & Is Applied Only After The Connector Has Been 100% Leak Tested, Prior To Nut & Fitting Assembly, Use With Natural & LP Gases, Approved For Indoor & Outdoor, Temperature Rating: -40 Degrees Fahrenheit To 150 Degrees Fahrenheit, Maximum Pressure Rating 1/2 PSI, CSA Certified.

From the Manufacturer

BrassCraft’s 1/2 In. FIP x 1/2 In. MIP x 72 In. ProCoat Gas Appliance Connector is 1/2 In. OD (3/8 In. ID) tube with a maximum operating capacity of 49,100 BTU’s. This ProCoat stainless steel gas connector is engineered with added safety in mind. The proprietary polymer coating is designed to withstand prolonged exposure to harsh household chemicals, UV rays and salt. ProCoat is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly onto the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

Product Description

Brass Craft’s 1/2 In. FIP x 1/2 In. MIP x 72 In. Recoat Gas Appliance Connector is 5/8 In. OD (1/2 In. ID) tube with a maximum operating capacity of 86,000 BTU’s. This Recoat stainless steel gas connector is engineered with added safety in mind. The proprietary polymer coating is designed to withstand prolonged exposure to harsh household chemicals, UV rays and salt. Recoat is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the Recoat coating is baked directly onto the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

From the Manufacturer

BrassCraft’s 1/2 In. FIP x 1/2 In. MIP x 72 In. ProCoat Gas Appliance Connector is 5/8 In. OD (1/2 In. ID) tube with a maximum operating capacity of 86,000 BTU’s. This ProCoat stainless steel gas connector is engineered with added safety in mind. The proprietary polymer coating is designed to withstand prolonged exposure to harsh household chemicals, UV rays and salt. ProCoat is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly onto the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

Product Description

SD Series, 60″, Pro-Coat Epoxy Coated, Stainless Steel, Gas Appliance Connector, 3/8″ I.D. x 1/2″ O.D. Tube, 1/2″ Female Pipe Thread x 1/2″ Male Pipe Thread, Product Comes in Re-Sealable Zip lock Bags, AGA Approved & IAS Design Certified For Indoor/Outdoor Use, Recommended For Forced Air Heaters, Gas Ranges, Furnaces, & Water Heaters.

From the Manufacturer

Brasscraft CSSD54-60 Gas Dryer and Water Heater Flex-Lines .

Duratrac gas connectors are CSA certified to ANSI Z21.24 CSA/CGA 6.10 Standard connectors for gas appliance and ANSI Z21.75 CSA/CGA 6.27 Standard Connectors for outdoor gas appliance and manufactured homes. The corrosion resistant yellow coating protects the product from exposure from harsh weather and certain chemicals. Refer to chart for BTU rating.

Purchase tip: This item is for large Btu demand appliances requiring 1″ OD pipe diameter and 3/4″ end fittings, applicable for appliances such as tankless water heater (over 150,000 Btu), commercial tank water heater, large space heater, large furnace, commericial fryer, commercial dryer, commericial oven, and commercial restaurant equipments. For smaller appliances such as 30, 40, 50, 75, 100 gallon residential gas water heaters, oven, cooktop, small tankless water heater less than 150,000 Btu, residential dryer, residential fire place, residential furnace and space heater use 1/2″ OD pipe diameter with 1/2″ fittings.